基于数值模拟的嘉兴城区河网水文特征

基于MIKE 11河网水动力模型,利用2010年—2019年实测气象水文资料,分析了嘉兴城区大包围圈内外主要河流的入流和出流特征.结果显示:嘉兴城区主要来流河道是苏州塘和杭州塘,出流河道主要为长纤塘、嘉善塘和平湖塘;平均来流量为88.2 m3/s,出流量为93.3 m3/s;年均和月均来流量变化较大,最枯月的平均来流量为50.1 m3/s,90％保证率枯水月的平均来流量为59.3 m3/s;大包围圈内部河道的平均流量为28.3 m3/s,平均出流量为19.1 m3/s,这表明大量外部来水未进入大包围圈内部河道,而是通过环郊河"短路"绕过嘉兴城区,流向东北;大包围圈内部河道的最枯月平均入流量为14.5 m3/s,90％保证率枯水月的平均入流量为18.3 m3/s.研究结果可为嘉兴城区河网综合规划和生态治理提供科学依据.     

铁的磷酸盐纳米颗粒的控制合成及表征

以FeCl3·6H2O、Na3 PO4和NaAc为原料,以乙二醇与水的混合物为溶剂,通过溶剂热法在210℃的条件下反应8h制备了铁的磷酸盐纳米颗粒.通过改变溶剂中乙二醇与水的量、Na3PO4的量、NaAc的量可以得到不同尺寸的铁的磷酸盐纳米颗粒样品.利用扫描电子显微镜(SEM)和X-射线粉末衍射(XRD)手段对产物的形貌和结构进行了表征和研究.     

Coupling Interrupted Fischer and Multicomponent Joullié-Ugi to Chase Chemical Diversity: from Batch to Sustainable Flow Synthesis of Peptidomimetics

The generation of peptidomimetic substructures for medicinal chemistry purposes requires effective and divergent synthetic methods. We present in this work an efficient flow process that allows quick modulation of reagents for Joullié-Ugi multicomponent reaction, using spiroindolenines as core motifs. This sterically hindered imine equivalent could successfully be diversified using various isocyanides and amino acids in generally good space-time yields. A telescoped flow process combining interrupted Fischer reaction for spiroindolenine synthesis and subsequent Joullié-Ugi-type modification resulted in product formation in very good overall yield in less than 2 hours compared to 48 hours required in batch mode. The developed protocol can be seen as a general tool for rapid and facile generation of peptidomimetic compounds. We also showcase preliminary biological assessments for the prepared compounds.     

Linearity Performance Analysis of Double Gate (DG) VTFET Using HDB for RF Applications

Silicon - In recent low-power electronics industry, Tunnel field-effect transistors (TFETs) have shown the superior performance such as decreased leakage current and lower subthreshold slope (SS)....     

Digital image correlation analysis and modelling of the strain rate in metal cutting

In the last eight decades, considerable modelling and computational efforts have been made to predict the strain rate during cutting with the aim of optimizing machining processes. However, the validation of these modelling approaches on a local scale remains excessively limited due to the lack of in-situ measurements and the faulty existing quick-stop tests. This work presents the in-process analysis of the strain rate and strain in the primary shear zone using high speed Digital Image Correlation (DIC) techniques. The comparison of measured and computed results shows the suitability of the DIC techniques and the robustness of the modelling approaches.     

A priori performance assessment of line-less mobile assembly systems

Present assembly systems are often based on rigid, line-based approaches and are hindered in their reconfiguration capability. Line-less Mobile Assembly Systems (LMAS) are a novel approach for assembly organization. They improve flexibility through mobile resources, permitting spatiotemporal freedom in scheduling and resource assignment. This paper presents a method for a priori assessment of LMAS during the early stages of the assembly system design process. The method applies a modified, extended mean value analysis to a closed queuing network representation of LMAS to estimate performance. The method is validated model analysis and comparison on two use cases indicating plausible model behavior.     

A new strategy to reduce edge chipping using stress wave impedance matching

To restrain edge chipping and elucidate its mechanism during machining, the initiation of edge chipping was investigated in this study from the propagation properties of stress waves in the fractured media. Three technological principles of the support for chipping suppression were proposed to reduce the intensity of reflected extension waves, namely, the wave impedance matching, the smaller residual gap and the higher viscosity of the gap filler between the workpiece and the support. As demonstrated from the experimental results, using brass support with non-solid epoxy gap filler can significantly restrain the edge chipping of pressureless sintered silicon carbide during grinding.     

Preconditioning of AISI 304 stainless steel surfaces in the presence of flavins—Part II: Effect on biofilm formation and microbially influenced corrosion processes

Biofilm formation and microbially influenced corrosion of the iron-reducing microorganism Shewanella putrefaciens were investigated on stainless steel surfaces preconditioned in the absence and presence of flavin molecules by means of XANES (X-ray absorption near-edge structure) analysis and electrochemical methods. The results indicate that biofilm formation was promoted on samples preconditioned in electrolytes containing minute amounts of flavins. On the basis of the XANES results, the corrosion processes are controlled by the iron-rich outer layer of the passive film. Biofilm formation resulted in a cathodic shift of the open circuit potential and a protective effect in terms of pitting corrosion. The samples preconditioned in the absence of flavins have shown delayed pitting and the samples preconditioned in the presence of flavins did not show any pitting in a window of −0.3- to +0.0-V overpotential in the bacterial medium. The results indicate that changes in the passive film chemistry induced by the presence of minute amounts of flavins during a mild anodic polarization can change the susceptibility of stainless steel surfaces to microbially influenced corrosion.     

基于C#持久蠕变强度外推功能的实现

持久蠕变强度外推是预测材料在高温高压环境下工作寿命的有效方法。目前常用的外推方法有等温法和参数法。这两种方法都是通过在实验室中采用较短时间的试验，获取试验数据后，通过Excel或者MATLAB等数据处理软件进行数据的拟合处理和外推计算。这些数据归纳统计和数学建模的过程有时需要耗费试验人员的大量精力。介绍了持久蠕变强度外推的软件实现方法，该功能包含在持久蠕变试验设备配备的软件中，试验完成后，软件直接根据试验结果进行数据拟合和持久蠕变强度的外推计算，无需试验数据的统计和建模，大大提高了持久蠕变强度外推计算的效率。     

Prediction models for multiphase-flow-induced corrosion of API X80 steel in CO2/H2S environment

In the offshore oil and gas industry, mainly focusing on the use of rigid or flexible pipes of subsea infrastructure applied to risers or flowlines, one of the greatest difficulties is the interpretation of the combined effects of the various correlated phenomena (hydrodynamic effects of intermittent flow, the effects of corrosivity of the environment in addition to variations in pressure, temperature, and dynamic loading). On the basis of this scenario, defining the degree of severity of each of the correlated system variables becomes of fundamental importance for establishing reliable criteria for selecting materials for subsea application. The established flow pattern directly affects the corrosion rate (or the pipe material mass loss), but the balance of other variables including possible changes in the physical and transported fluid chemical properties may increase the damage up to an order of magnitude, which is a piece of information normally not foreseen in design criteria. Therefore, to improve the understanding of the corrosion study influenced by multiphase flow, a testing loop was designed and assembled at the Corrosion and Protection Laboratory of the Institute for Technological Research, in which API X80 steel coupons were positioned in locations with a 0° and 45° inclinations. Tests were conducted by varying the partial pressure of the gaseous phase containing blends of CO₂ and H₂S with N₂ balance, mixed with the liquid phase containing light oil and heavy oil in water with salinity (NaCl)-simulating oil well conditions with 80% water cut. The main objective of this study is to establish models that can predict the corrosion intensity in conditions close to those obtained experimentally. To achieve results, the multiple regression and Box–Cox transformation methods were applied. These models will make possible damage prediction and optimization of matrix parameters for the multiphase-loop test.